SuperUser Account

Digitizing Trees, Leaves, Grass and Bushes

In a previous article, I showed how stitch direction and stitch type can be used in a creative way to make more realistic landscapes. Now we will focus more on individual areas, mainly trees, bushes, and leaves.

A lot of designs that come around show thin outlines to create detail. That’s good for print, but not practical for embroidery. Try convincing your client to drop these outlines. When you have outlined, you are more likely to let the outlines do all the thinking for you, your designs are more likely to be flat and underwhelming. You should let stitch type and direction give you the detail. It may be just a little more work, but a great way to impress an important client.

The objects in this article are all left chest size images, not full backs. Although there are many different embroidery software, I will be primarily focusing on Wilcom.

Pine Trees (Conifers)

The main characteristic of Pine trees is that it is a needle bearing tree and does not have leaves. The branches of pine trees can be fairly easily created.

fig1_tree
Fig 1

A row of pine trees can be done several ways. One way to approach this is to use a complex fill stitch going vertical or near vertical and having random pattern put to it. In Pulse use the fill stitch labeled Random. In Wilcom, you will have to go into the settings in Tatami and change the A pattern to .5 and the B pattern to 0. Add a percentage to Random of 15 to 80%.

 

fig2_tree
Fig 2

You can add even more depth by dividing the clump of trees into several rows of the same stitch fill, one on top another. Another simple but impressive way is using satin stitch with Auto Split Stitch on (known as random split stitch in Pulse.) Feel free to turn it down from the standard 7 mm until the split sections look even with the bottom of the branches (Fig. 3).

fig3_tree
Fig 3

On individual trees that are more of the focus of the design you may want to put more detail into it. First of all, even though you may see individual branches, never go crazy and try to duplicate each branch. It’s both too much work and too many stitches when dealing with overlapping of branches. Simulation of the branches is just fine. If the spacing between branches needs to be over 7 mm, I suggest switching from satin with a split stitch to Tatami with A pattern to 1 and B pattern to 0 and adjust the random and stitch length until the pattern starts lining up with the branches (Fig 2.) Add a jagged edge pointing downward and you will get a nice representation of the needles.

 

 

Leafy Trees (Deciduous)

fig4_tree
Fig 4 – Line art of a leafy tree

When digitizing trees, do not try to do individual leaves. Three simple techniques I can suggest:

 

1) Complex fill with Tatami stitch (Fig. 6) This can be quite boring, but if done right, can be a quick and effective way. First, the stitch direction should be more vertical. You go horizontal, and it will be flat and boring. For Pulse, choose the fill pattern labeled Random. For Wilcom, go into Object Properties and select Tatami fill. Change the offset to A: 0 B: 1.00 and turn random on 80. It will give a nice organic feel.

 

 

 

fig5_tree
Fig 5 – Standard Tatami fill stitch. Direction of fill stitch is almost vertical. Wilcom Object Properties: Offset A:.25 / Offset B:.25 / Random:0

 

2) Find the pattern in the tree clumps, and simplify this into several groupings (Fig. 7). Play with the direction of each clumping and use satin stitching with split stitching enacted. The difficulty with this technique is making it look like one entire object and not just a bunch of clumps.

 

 

 

 

 

 

fig6_tree
Fig 6 – Tatami fill stitch with random applied. Direction of fill stitch is almost vertical. Wilcom Object Properties: Offset A:0 / Offset B: 1 / Random:80
fig7_tree
Fig 7 – Tree has been divided in to smaller groups of Satin stitch with split stitch applied, various angles. Wilcom Object Properties: Split stitch selected with a length of 5mm.
fig8_tree
Fig 8 – Combination of Fig 6 and Fig 7. Tree has been divided into smaller groups with similar Tatami fill as Fig 6 with only slightly offset vertical direction. Wilcom Object Properties: Offset A: .5 / Offset B: 1 / Random: 80

 

 

 

 

 

 

 

 

 

 

 

 

3) Similar to #2, create clumps, but instead of using satin/split stitch, use Tatami fill with a nice random pattern (Fig 8.) With this technique, have all of the clumps go in a similar stitch direction. This will allow the clumps to be more unified but still be interesting.

 

 

 

 

 

 

 

Leaves

fig9_tree
Fig 9 – Different stitch direction makes for more interesting leaves.

For your traditional leaf, create the division in the leaf by using two different stitch directions. Do the stitch direction in a herringbone style (Fig. 9.) Angle your stitches one way for one side of the leaf and the opposite for the other side of the leaf, overlapping slightly.

Grass

Although it is tempting do to every blade of grass in some designs, and you have nothing else to do, don’t do it. It might have more depth and characteristic by doing so, but you also get a problem of too many stitches in an area which usually makes the design dense and causes the design to warp. You may also get thread breaks. So my suggestion, is use a fill stitch for the majority of the area and then just suggest a few blades of grass on top of the fill with a satin stitch. Generally, you can even lower the density of the satin stitch since it will be green on green.

Hedges and Bushes

fig10_tree
Fig 10 – Hedge showing randomized Tatami fill stitch with slight jagged edge on both sides.

Generally, bushes and hedges can be approached the same way. I like to use a large percentage of random in my Tatami stitch and use an offset fraction of A: .5 and B: 1.00 and a random at around 80%. I also like to use a bit of jagged edge (both sides) of .6 mm. Just enough to give it a slight roughness. The direction should always be between an angle of 45 degrees to 90 degrees to give it loft (Fig. 10.) Just horizontal will make it flat and you want your bushes and hedges to stand out from the background. Have fun playing around with stitch type and pattern. The more you experiment, the more you will learn. Although putting the image on True View or 3D (Pulse) isn’t as good as an actual sew out, use it as a guide to give you an idea if

Have fun playing around with stitch type and pattern. The more you experiment, the more you will learn. Although putting the image on True View or 3D (Pulse) isn’t as good as an actual sew out, use it as a guide to give you an idea if your are close to getting what you want. Most of these techniques do not take much a lot more time than just flat embroidery, so go ahead and try. You and your customer will enjoy the outcome.

 

Have any questions? Contact us:

service@ignitiondrawing.com               253-284-0733                 ignitiondrawing.com

Previous Article Digitizing Landscapes
Next Article Embroidery Glossary Stitch Types
Print
6909 Rate this article:
No rating

1 comments on article "Digitizing Trees, Leaves, Grass and Bushes"

Avatar image

haroldcoyer

Thanks for your article. Your article is very informative and giving the best knowledge. I

have seen a website that gives me the best Embroidery digitizing at a very affordable cost.

Leave a comment

This form collects your name, email, IP address and content so that we can keep track of the comments placed on the website. For more info check our Privacy Policy and Terms Of Use where you will get more info on where, how and why we store your data.
Add comment

Theme picker

Tackle Twill: A Guide

Tackle Twill: A Guide

Tackle Twill is an embroidery method that involves replacing part of a design with fabric instead of thread to save on stitch count or create a unique look.

CorelDraw Users: Vector Art with Gradients

CorelDraw Users: Vector Art with Gradients

Have you ever ordered a vector file in EPS format but when you view it in CorelDraw the image looks jagged and blurry like a low-resolution jpeg?

Stop That Sinking Feeling

Stop That Sinking Feeling

Do you fi­nd your embroidery looks like it is disappearing or sinking into the fabric? When embroidering on high pile fabrics such as polar fleece, sweaters, or towels, your design may bene­fit from Knockdown Stitches, which flatten that pile—letting your embroidery stand out!

Survey Results, Steady Improvements

Survey Results, Steady Improvements

First of all, thank you all who participated in our annual survey!  We appreciate your candor and feedback about our processes, our people, and our services. What did we learn? 

Gaining Visibility into Satisfaction Rates

Gaining Visibility into Satisfaction Rates

"Rate Your Project" is the latest new feature on your Ignition Drawing Dashboard: Simply click to report your satifsfaction level. 

 

Vector File Formats

Vector File Formats

You’ve browsed our site and are placing a vector order, then find you're stumped by all the various file format options. Which one do you need?  What are they used for?  We're here to help! 

Stitch Counts

Stitch Counts

WHAT WE KNOW FOR SURE:
QUALITY EMBROIDERY REQUIRES OPTIMIZED STITCH COUNT

Here at Ignition Drawing, we know what it takes to get every stitch count “Just Right” every time.  

New Year, New Starts!

New Year, New Starts!

This year, newcomer Anjuli joins our staff and we welcome back Andrea! 
Longtime embroidery expert Jesse Elliot steps back as our joint team leader. 

RSS
12345