SuperUser Account

Small Lettering Guide – Part 1

Twill/Denim/Nylon

suitable.jpg
Fig 1.1 Height of letters are determined by measuring the capital X. Also known as X-height.

With fabrics such as twill, denim, or nylon, embroidery does not sink much and generally floats on top of the fabric. This creates less of a need for underlay and shorter pull compensation, thus allowing us to go smaller with text than other fabrics.

What Is The Smallest I Can Go?

Absolute minimum height for all caps is 5mm/.18. Absolute minimum for upper and lower case letters is 6.2mm/.24″. Letter stroke can be no smaller than .66mm/0.24, as seen  below:

height.jpg

 

 

 

 

 

 

 

Do You Have Examples Of Good And Bad Text?

We do! Check out below the difference following our advice can make:

badex
These designs don’t follow the rules, and you can see the corners of the text are pointy and pushing out, small letter quality is variable. Excessive underlay causes issues for them.
goodone
These designs were made following our rules. Letters look straight and even, with minimal underlay coming out and no misshaping.

 

Fleece/Heavy Knits/Towels 

Fabrics such as polar fleece, towels and heavy knits like beanies can create a lot of issues when embroidering. First of all, the polar fleece and heavy knits have plenty of stretch. Second, all three types have a pile that can distort or hide the embroidery.

1
Fig. 3.1

Underlay can prevent the letters from sinking and distorting their shapes, however thinner strokes do not have enough room for the type and amount of underlay needed (fig 3.2.)

 

This is where tackdown comes in. Tackdown is an open layer of ceeding (also known as Tatami or fill stitch) laying down in one direction and again in the opposite direction to make an x pattern that provides a more stable surface for the embroidery (fig. 3.1, 3.3, and 3.4.)

 

2
Fig. 3.2 – The above set is too thin for the amount of underlay needed for fleece, towels and heavy knits. Tackdown would help tremendously with this font. This font is 6.4 mm/.25″ High and at the minimum recommended for fleece with a tackdown.

 

 

 

 

 

 

 

 

 

 

3
Fig. 3.3 – A criss-crossing formation made of run stitches or open tatami fill tamps down the area behind and around the design, keeping troublesome pile of fabric from peaking through or covering the design. It also helps keep the fabric from stretching and limits distortion of the stitching.
4
Fig. 3.4 – Finished product on polar fleece. Note how the ends in the N and k of “No Tackdown” appear to sink and or shift while the letters in “With Tackdown” all look straight, even and bolder. All letters were digitized with the same stroke width.

 

 

 

 

 

 

 

 

5
Fig. 4.1 – Letters should be thick and tall. This is recommended minimum for fleece, towels and heavy knits without tackdown. 7.6mm/.3″ in height.

Tackdown keeps the letters from sinking as much and also makes a barrier away from the letters to keep high pile fabric from covering the embroidery. Without tackdown, you will need bigger and bolder letters (fig. 4.1.) Even then, there may still be issues some issues with the fabric peaking through or over letters.

 

Making the tatami stitch open reduces the amount of stitches. The tackdown is always meant to match the color of the garment so it is less obtrusive than just a box of regular tatami stitching.

 

6
Fig 4.2 – This is stock lettering on a knit beanie. Distortion is quite noticeable especially in the F and T. This is a great candidate for water soluble topping.

Tackdown can be any shape you want and can go around an entire logo if necessary.

Sometimes you just can’t use tackdown. Maybe size does not allow it, or the customer just doesn’t like it, or if you are using stock lettering that just isn’t coming out right. If you find yourself with a design that isn’t working try a water soluble topping (fig. 4.2 and 4.3.)

7
Fig. 4.3 – Water soluble topping is applied on top of the garment before embroidering. After embroidery is complete, tear away the larger pieces, then pick out as much of the smaller pieces. Then dab lightly with a damp cloth or a steamer.

Just apply a layer or two to the surface of the fabric and start embroidering. To remove the topping, tear it away and pick out as much remaining pieces as you can. Then lightly dab with wet cloth or steamer.

Polos/Pique/Performance Wear

polos

Pique, tees, and performance wear are stretchy and small lettering gets more difficult. With these fabrics, there is a need for more underlay. Underlay will help stabilize the stretchines and in the case of pique and tees, also prevent excessive sinkage.

Absolute Minimum Height for All Caps is 5.5mm/.21”

Absolute Minimum for Upper & Lower Case Letters is 6.2mm/.24”.

Letter stroke can be no smaller than .6mm

 

 

 

 

 

 

 

Have any questions? Contact us:

service@ignitiondrawing.com               253-284-0733                 ignitiondrawing.com

Previous Article Small Lettering Guide – Part 2
Next Article Needle Options
Print
7249 Rate this article:
No rating

Leave a comment

This form collects your name, email, IP address and content so that we can keep track of the comments placed on the website. For more info check our Privacy Policy and Terms Of Use where you will get more info on where, how and why we store your data.
Add comment

Theme picker

Tackle Twill: A Guide

Tackle Twill: A Guide

Tackle Twill is an embroidery method that involves replacing part of a design with fabric instead of thread to save on stitch count or create a unique look.

CorelDraw Users: Vector Art with Gradients

CorelDraw Users: Vector Art with Gradients

Have you ever ordered a vector file in EPS format but when you view it in CorelDraw the image looks jagged and blurry like a low-resolution jpeg?

Stop That Sinking Feeling

Stop That Sinking Feeling

Do you fi­nd your embroidery looks like it is disappearing or sinking into the fabric? When embroidering on high pile fabrics such as polar fleece, sweaters, or towels, your design may bene­fit from Knockdown Stitches, which flatten that pile—letting your embroidery stand out!

Survey Results, Steady Improvements

Survey Results, Steady Improvements

First of all, thank you all who participated in our annual survey!  We appreciate your candor and feedback about our processes, our people, and our services. What did we learn? 

Gaining Visibility into Satisfaction Rates

Gaining Visibility into Satisfaction Rates

"Rate Your Project" is the latest new feature on your Ignition Drawing Dashboard: Simply click to report your satifsfaction level. 

 

Vector File Formats

Vector File Formats

You’ve browsed our site and are placing a vector order, then find you're stumped by all the various file format options. Which one do you need?  What are they used for?  We're here to help! 

Stitch Counts

Stitch Counts

WHAT WE KNOW FOR SURE:
QUALITY EMBROIDERY REQUIRES OPTIMIZED STITCH COUNT

Here at Ignition Drawing, we know what it takes to get every stitch count “Just Right” every time.  

New Year, New Starts!

New Year, New Starts!

This year, newcomer Anjuli joins our staff and we welcome back Andrea! 
Longtime embroidery expert Jesse Elliot steps back as our joint team leader. 

RSS
12345