SuperUser Account

Digitizing Trees, Leaves, Grass and Bushes

In a previous article, I showed how stitch direction and stitch type can be used in a creative way to make more realistic landscapes. Now we will focus more on individual areas, mainly trees, bushes, and leaves.

A lot of designs that come around show thin outlines to create detail. That’s good for print, but not practical for embroidery. Try convincing your client to drop these outlines. When you have outlined, you are more likely to let the outlines do all the thinking for you, your designs are more likely to be flat and underwhelming. You should let stitch type and direction give you the detail. It may be just a little more work, but a great way to impress an important client.

The objects in this article are all left chest size images, not full backs. Although there are many different embroidery software, I will be primarily focusing on Wilcom.

Pine Trees (Conifers)

The main characteristic of Pine trees is that it is a needle bearing tree and does not have leaves. The branches of pine trees can be fairly easily created.

fig1_tree
Fig 1

A row of pine trees can be done several ways. One way to approach this is to use a complex fill stitch going vertical or near vertical and having random pattern put to it. In Pulse use the fill stitch labeled Random. In Wilcom, you will have to go into the settings in Tatami and change the A pattern to .5 and the B pattern to 0. Add a percentage to Random of 15 to 80%.

 

fig2_tree
Fig 2

You can add even more depth by dividing the clump of trees into several rows of the same stitch fill, one on top another. Another simple but impressive way is using satin stitch with Auto Split Stitch on (known as random split stitch in Pulse.) Feel free to turn it down from the standard 7 mm until the split sections look even with the bottom of the branches (Fig. 3).

fig3_tree
Fig 3

On individual trees that are more of the focus of the design you may want to put more detail into it. First of all, even though you may see individual branches, never go crazy and try to duplicate each branch. It’s both too much work and too many stitches when dealing with overlapping of branches. Simulation of the branches is just fine. If the spacing between branches needs to be over 7 mm, I suggest switching from satin with a split stitch to Tatami with A pattern to 1 and B pattern to 0 and adjust the random and stitch length until the pattern starts lining up with the branches (Fig 2.) Add a jagged edge pointing downward and you will get a nice representation of the needles.

Leafy Trees (Deciduous)

fig4_tree
Fig 4 – Line art of a leafy tree

When digitizing trees, do not try to do individual leaves. Three simple techniques I can suggest:

 

1) Complex fill with Tatami stitch (Fig. 6) This can be quite boring, but if done right, can be a quick and effective way. First, the stitch direction should be more vertical. You go horizontal, and it will be flat and boring. For Pulse, choose the fill pattern labeled Random. For Wilcom, go into Object Properties and select Tatami fill. Change the offset to A: 0 B: 1.00 and turn random on 80. It will give a nice organic feel.

 

fig5_tree
Fig 5 – Standard Tatami fill stitch. Direction of fill stitch is almost vertical. Wilcom Object Properties: Offset A:.25 / Offset B:.25 / Random:0

 

2) Find the pattern in the tree clumps, and simplify this into several groupings (Fig. 7). Play with the direction of each clumping and use satin stitching with split stitching enacted. The difficulty with this technique is making it look like one entire object and not just a bunch of clumps.

 

fig6_tree
Fig 6 – Tatami fill stitch with random applied. Direction of fill stitch is almost vertical. Wilcom Object Properties: Offset A:0 / Offset B: 1 / Random:80
fig7_tree
Fig 7 – Tree has been divided in to smaller groups of Satin stitch with split stitch applied, various angles. Wilcom Object Properties: Split stitch selected with a length of 5mm.
fig8_tree
Fig 8 – Combination of Fig 6 and Fig 7. Tree has been divided into smaller groups with similar Tatami fill as Fig 6 with only slightly offset vertical direction. Wilcom Object Properties: Offset A: .5 / Offset B: 1 / Random: 80

3) Similar to #2, create clumps, but instead of using satin/split stitch, use Tatami fill with a nice random pattern (Fig 8.) With this technique, have all of the clumps go in a similar stitch direction. This will allow the clumps to be more unified but still be interesting.

Leaves

fig9_tree
Fig 9 – Different stitch direction makes for more interesting leaves.

For your traditional leaf, create the division in the leaf by using two different stitch directions. Do the stitch direction in a herringbone style (Fig. 9.) Angle your stitches one way for one side of the leaf and the opposite for the other side of the leaf, overlapping slightly.

Grass

Although it is tempting do to every blade of grass in some designs, and you have nothing else to do, don’t do it. It might have more depth and characteristic by doing so, but you also get a problem of too many stitches in an area which usually makes the design dense and causes the design to warp. You may also get thread breaks. So my suggestion, is use a fill stitch for the majority of the area and then just suggest a few blades of grass on top of the fill with a satin stitch. Generally, you can even lower the density of the satin stitch since it will be green on green.

Hedges and Bushes

Fig 10 – Hedge showing randomized Tatami fill stitch with slight jagged edge on both sides.

Generally, bushes and hedges can be approached the same way. I like to use a large percentage of random in my Tatami stitch and use an offset fraction of A: .5 and B: 1.00 and a random at around 80%. I also like to use a bit of jagged edge (both sides) of .6 mm. Just enough to give it a slight roughness. The direction should always be between an angle of 45 degrees to 90 degrees to give it loft (Fig. 10.) Just horizontal will make it flat and you want your bushes and hedges to stand out from the background. Have fun playing around with stitch type and pattern. The more you experiment, the more you will learn. Although putting the image on True View or 3D (Pulse) isn’t as good as an actual sew out, use it as a guide to give you an idea if

Have fun playing around with stitch type and pattern. The more you experiment, the more you will learn. Although putting the image on True View or 3D (Pulse) isn’t as good as an actual sew out, use it as a guide to give you an idea if your are close to getting what you want. Most of these techniques do not take much a lot more time than just flat embroidery, so go ahead and try. You and your customer will enjoy the outcome.

 

Have any questions? Contact us:

service@ignitiondrawing.com               253-284-0733                 ignitiondrawing.com

Previous Article Digitizing Landscapes
Next Article Embroidery Glossary Stitch Types
Print
25217 Rate this article:
5.0

12 comments on article "Digitizing Trees, Leaves, Grass and Bushes"

Avatar image

haroldcoyer

Thanks for your article. Your article is very informative and giving the best knowledge. I

have seen a website that gives me the best Embroidery digitizing at a very affordable cost.


Avatar image

Tim

Greetings, it was a really brilliant adventure for me when I looked around your website. I just needed to praise you on the outstanding quality of the work and to send you all the best with it as you develop from now on. It was a pleasure to explore your blog and I will most definitely be stopping by again soon to see how you're getting on. Thanks a ton and I'll no doubt see you here again very soon - Montague Handyman


Avatar image

Tim

Howdy, it turned out to be a really incredible experience for me when I called in at your website. I hope you don't mind if I compliment you on the quality of the work and to send you good luck with it as you progress in the future. It was nice to browse your web site and I will surely be stopping by again shortly to find how you are doing. Thanks a ton and I shall see you here soon - Pablo Driveway


Avatar image

Damp

I like the way you solve the individual leaves problem, good stuff - Damp Proofing


Avatar image

andrew

I've have read your blog. Honestly I've never read this type of blog before. Appreciate your work and will love to read your incoming articles too.

We provide online image digitizer service that can also fulfill your embroidery needs.


Avatar image

John Edwart

I've read your article. Honestly, I've never read this type of informative and efficient article before. This article will help lots of beginners like me to build skills in embroidery. Love to read your incoming blogs too. Really appreciate your work and dedication.

We have https://crystaldigitizing.com/custom-embroidery-digitizing/ to fulfill your embroidery needs.


Avatar image

duck life

You have a very good embroidery ability, it looks so vivid.


Avatar image

basket

This stitch design looks really perfect, I would like to draw a basketball figure with this stitch method, I don't know if I can do it.



Avatar image

jamessmith

That's great


Avatar image

uno online

I like your post. See my name!


Leave a comment

This form collects your name, email, IP address and content so that we can keep track of the comments placed on the website. For more info check our Privacy Policy and Terms Of Use where you will get more info on where, how and why we store your data.
Add comment

Theme picker

Digitizing Animals

Digitizing Animals

We are going to look at this subject with a rather broad brush. This article will handle the basics of how to approach digitizing for animals. I use Wilcom as my primary digitizing program so most of my specifications will focus...

Continue Reading →

Day 1 of your Layout Lab Private Label

Day 1 of your Layout Lab Private Label

If you're reading this blog you might be looking for advice on where to get started or how to get your Layout Lab off the ground. We are giving you a free 30-day trial so its a great opportunity for...

Continue Reading →

Corners and Capping

Corners and Capping

Digitizing can be more complex than you think. Something that may seem simple can actually be really difficult to get right. This is true about digitizing corners. What’s so difficult about corners in outlines? You just make a line, transform...

 

Continue Reading→

An introduction to Layout Lab tools

An introduction to Layout Lab tools

With Layout Lab, creating a design only takes minutes, and saves time with your creative projects, without the need of expensive design software. Put the tools in your customers' hands with your very own Private Label Designer. Getting started is easy...

Continue reading →

All you need to know about Filling White Space

All you need to know about Filling White Space

When filling out your embroidery order you will come across the Fill White Space button. What does fill white space mean? Most artwork presented to us is on a white background, but the question is relevant when there is also...

Continue Reading →

RSS
12345