Corners and Capping
SuperUser Account

Corners and Capping

Digitizing can be more complex than you think. Something that may seem simple can actually be really difficult to get right. This is true about digitizing corners.

What’s so difficult about corners in outlines? You just make a line, transform to a satin stitch and you are good to go, right? Well, sort of. This article will be focusing on how and when to adjust corners in a design. I use Wilcom, but you can do the same things in Pulse and Design Shop, just the language might be slightly different.

The Basics

Let’s first go into how the spacing in satin stitches is produced. For a simple straight line, spacing is going to be evenly distributed from point A to point B(Fig 1).

fig1
Fig 1 – Straight line stitching

When you add a corner, things change. The spacing is predicated by the angle. So when you start with a line that is straight, then goes into a corner, the angle of that corner determines the spacing. What this means, is the spacing will be wider at the corners than at the straight end. They will also be wider the further out you go. So the thicker the line, the wider spacing for the outer edge of the stitch(Fig 2).

fig2v2
Fig 2

The other thing that happens, is how pull compensation is affected. Pull compensation goes directly out from the stitch, so if you have a stitch that is vertical, then the pull compensation will go directly up. Now at the same corner, the pull compensation will follow the angle so it will actually appear shorter than the straight up and down part. The more compensation is needed, the more this will be noticeable.

When using input C (also known as Steil stitch in Pulse) you have an option of Fractional Spacing which helps determine the point the stitch direction changes from perpendicular to following the angle of the corner.

On a hand created border such as input A in Wilcom and Column Tool in Pulse, a border is made by creating the inside and outside edges. If you just go from corner to corner, you will get a gradual angle of stitch direction along with the spacing appearing wider.

For thin borders (approximately 1.5 mm wide and smaller), that are more obtuse such as an octagon, simply going from corner to corner will do. A better option is to go from corner to corner and add direction lines going perpendicular somewhere near the corners. This will help keep the border from looking bowed in the middle and reduce the amount of area that will have wider spacing between stitches. Acute angles such as the points of stars would require this technique(Fig 3).

fig3
Fig 3

Mitre and Caps

Now we will explore mitre, hand mitred, and caps. A mitre corner consists of a stitch that tapers into and out of the corner with an overlap where the two lines meet (think a picture frame.) To mitre a corner, go into object properties>FX>/smart corners and select mitre corners. You can tell it at what sharpness of an angle you want it to activate. You can also have control of how much overlap you use. Sweats and knits will need more overlap than nylon or twill(Fig 4).

Fig 4
fig4b
Fig 5

One important thing to keep in mind about mitred corners is that auto underlay does not adjust for the tapering. So you could end up with twice as much underlay in the corners then you need. This is more of a concern when going from extra wide widths, where the line will need more underlay. In this case, I suggest making a hand version and breaking up the corners so you can change the underlay in just those areas. In the hand version, instead of angling towards the corner, keep the stitch perpendicular and end just a stitch or two away from the corner. It may look wrong on screen, but will fill up the corner when sewn.

Capping consists of two conjoining lines meeting as one solid section at the outer corner. The change from two lines to one point can sometimes look jarring, so adjust the split stitch function to activate for a little bit of the width to provide a smoother transition (Fig 6.) Capping is perfect for doing small capital A’s.

fig6
Fig 6

Try comparing what it looks like when you hand do capping and when you use the auto cap corners function. You have more control when you hand digitize the capping (Fig 7), so try them both out and experiment with the controls.

fig7
Fig 7

Fig 8.  illustrates how much the angles really influence the shape and density of the line. On the left is normal pull compensation, but on the right, we have increased that pull compensation greatly to give you a closer look at how the lines are affected. Look closely at Angled Corner, Corner Fraction On and Mitre Corner. All of these show how the angle controls the final look of the lines.

Angles and pull comp
Fig 8 – Angles and pull comp

The best advice I can give you, is to try all of these methods and determine what works best for you. Factors such as different stroke widths and fabric types may require different corner styles.

 

Next Article Digitizing Animals
Print
25386 Rate this article:
No rating

18 comments on article "Corners and Capping"

Avatar image

Frank Fire

Thanks for your help, that looks great - Frank Fire


Avatar image

Tim

Aloha, I should say it was a really fabulous adventure for me when I looked around your website. I hope you don't mind if I congratulate you on the excellent quality of the work and to send you all the best with it as you advance as time goes on. It was a hoot to surf your website and I will surely be dropping by again before long to find how you are doing. Many thanks and I'll see you here before too long - Kylan Awnings


Avatar image

davidluis

I've read your embroidery article. This is really an amazing content you have described complete things about embroidery. This is really special for beginners to develop their embroidery skill. We have online digitizer that can also fulfill your embroidery needs.


Avatar image

gorilla tag

I am very enjoyed this blog. It's an informative topic. It helps me very much to solve some problems.


Avatar image

dordle

I was relieved to see your improved piece on your site because you have clearly come a long way. The more you write, the more I hope it improves.


Avatar image

pikashow app

The details you have put in this post is really helpful. It saved my time as I found all the details in this post itself. Keep updating us with more such posts. pikashow app



Avatar image

online games

It is so awesome. Your instruction is so detailed


Avatar image

wordle

Actually I don't understand much about angles and digitization, thanks to this article and some related articles available on this website I have understood more about this field, it is very useful for me and I Thank you very much for your sharing.


Avatar image

ltobets

หวยออนไลน์ ltobets เป็นอีกหนึ่งทางเลือกของคนชอบซื้อหวย


Avatar image

morse code translator

I actually don't know much about angles and digitization, but because of this article and a few others like it on this website, I now do. I appreciate you sharing this information greatly and feel like I've learned a lot about this subject.


Avatar image

Henry Liam

Is this information useful?

Is this information useful?

Is this [url=https://abdc.axd]information[/url] useful?

Is this [information](https://abdc.axd) useful?

Is this [https://abdc.axd information] useful?

Is this [link=https://abdc.axd]information[/link] useful?



Avatar image

JPG to Text

The jpg to text (image to text) converter is an online OCR tool that extracts text from images such as JPGs, PNGs, photos, SVGs, and other vector graphics.


Avatar image

redactle

Very good article; it provided me with a lot of useful knowledge. As a blog, please continue to share more. I've added it to my bookmarks so that I can keep up with you.


Avatar image

Beylikdüzü konut projeleri

The information here was very useful, thank you. Beylikdüzü konut projeleri



Leave a comment

This form collects your name, email, IP address and content so that we can keep track of the comments placed on the website. For more info check our Privacy Policy and Terms Of Use where you will get more info on where, how and why we store your data.
Add comment

Theme picker

Tackle Twill: A Guide

Tackle Twill: A Guide

Tackle Twill is an embroidery method that involves replacing part of a design with fabric instead of thread to save on stitch count or create a unique look.

CorelDraw Users: Vector Art with Gradients

CorelDraw Users: Vector Art with Gradients

Have you ever ordered a vector file in EPS format but when you view it in CorelDraw the image looks jagged and blurry like a low-resolution jpeg?

Stop That Sinking Feeling

Stop That Sinking Feeling

Do you fi­nd your embroidery looks like it is disappearing or sinking into the fabric? When embroidering on high pile fabrics such as polar fleece, sweaters, or towels, your design may bene­fit from Knockdown Stitches, which flatten that pile—letting your embroidery stand out!

Vector File Formats

Vector File Formats

You’ve browsed our site and are placing a vector order, then find you're stumped by all the various file format options. Which one do you need?  What are they used for?  We're here to help! 

Stitch Counts

Stitch Counts

WHAT WE KNOW FOR SURE:
QUALITY EMBROIDERY REQUIRES OPTIMIZED STITCH COUNT

Here at Ignition Drawing, we know what it takes to get every stitch count “Just Right” every time.  

Working with ZIP files

Working with ZIP files

Zip files(.zip) are compressed single files, sometimes called "archives", that contain one or more documents, photographs, videos or any variety of files. Zips make it easy to keep related files together similar to folders, but make transporting, e-mailing, downloading and...

Continue Reading →

Working With Monitor Coloration

Working With Monitor Coloration

"Why Can't You Match The Original Colors?" This is a question we get every now and then. We always strive to match colors as close as we can, but a few factors make it impossible to match 100%. One such...

Continue Reading →

RSS
12345