SuperUser Account

Small Lettering Guide – Part 1

Twill/Denim/Nylon

suitable.jpg
Fig 1.1 Height of letters are determined by measuring the capital X. Also known as X-height.

With fabrics such as twill, denim, or nylon, embroidery does not sink much and generally floats on top of the fabric. This creates less of a need for underlay and shorter pull compensation, thus allowing us to go smaller with text than other fabrics.

What Is The Smallest I Can Go?

Absolute minimum height for all caps is 5mm/.18. Absolute minimum for upper and lower case letters is 6.2mm/.24″. Letter stroke can be no smaller than .66mm/0.24, as seen  below:

height.jpg

 

 

 

 

 

 

 

Do You Have Examples Of Good And Bad Text?

We do! Check out below the difference following our advice can make:

badex
These designs don’t follow the rules, and you can see the corners of the text are pointy and pushing out, small letter quality is variable. Excessive underlay causes issues for them.
goodone
These designs were made following our rules. Letters look straight and even, with minimal underlay coming out and no misshaping.

 

Fleece/Heavy Knits/Towels 

Fabrics such as polar fleece, towels and heavy knits like beanies can create a lot of issues when embroidering. First of all, the polar fleece and heavy knits have plenty of stretch. Second, all three types have a pile that can distort or hide the embroidery.

1
Fig. 3.1

Underlay can prevent the letters from sinking and distorting their shapes, however thinner strokes do not have enough room for the type and amount of underlay needed (fig 3.2.)

 

This is where tackdown comes in. Tackdown is an open layer of ceeding (also known as Tatami or fill stitch) laying down in one direction and again in the opposite direction to make an x pattern that provides a more stable surface for the embroidery (fig. 3.1, 3.3, and 3.4.)

 

2
Fig. 3.2 – The above set is too thin for the amount of underlay needed for fleece, towels and heavy knits. Tackdown would help tremendously with this font. This font is 6.4 mm/.25″ High and at the minimum recommended for fleece with a tackdown.

 

 

 

 

 

 

 

 

 

 

3
Fig. 3.3 – A criss-crossing formation made of run stitches or open tatami fill tamps down the area behind and around the design, keeping troublesome pile of fabric from peaking through or covering the design. It also helps keep the fabric from stretching and limits distortion of the stitching.
4
Fig. 3.4 – Finished product on polar fleece. Note how the ends in the N and k of “No Tackdown” appear to sink and or shift while the letters in “With Tackdown” all look straight, even and bolder. All letters were digitized with the same stroke width.
5
Fig. 4.1 – Letters should be thick and tall. This is recommended minimum for fleece, towels and heavy knits without tackdown. 7.6mm/.3″ in height.

Tackdown keeps the letters from sinking as much and also makes a barrier away from the letters to keep high pile fabric from covering the embroidery. Without tackdown, you will need bigger and bolder letters (fig. 4.1.) Even then, there may still be issues some issues with the fabric peaking through or over letters.

 

Making the tatami stitch open reduces the amount of stitches. The tackdown is always meant to match the color of the garment so it is less obtrusive than just a box of regular tatami stitching.

 

6
Fig 4.2 – This is stock lettering on a knit beanie. Distortion is quite noticeable especially in the F and T. This is a great candidate for water soluble topping.

Tackdown can be any shape you want and can go around an entire logo if necessary.

Sometimes you just can’t use tackdown. Maybe size does not allow it, or the customer just doesn’t like it, or if you are using stock lettering that just isn’t coming out right. If you find yourself with a design that isn’t working try a water soluble topping (fig. 4.2 and 4.3.)

7
Fig. 4.3 – Water soluble topping is applied on top of the garment before embroidering. After embroidery is complete, tear away the larger pieces, then pick out as much of the smaller pieces. Then dab lightly with a damp cloth or a steamer.

Just apply a layer or two to the surface of the fabric and start embroidering. To remove the topping, tear it away and pick out as much remaining pieces as you can. Then lightly dab with wet cloth or steamer.

Polos/Pique/Performance Wear

polos

Pique, tees, and performance wear are stretchy and small lettering gets more difficult. With these fabrics, there is a need for more underlay. Underlay will help stabilize the stretchines and in the case of pique and tees, also prevent excessive sinkage.

Absolute Minimum Height for All Caps is 5.5mm/.21”

Absolute Minimum for Upper & Lower Case Letters is 6.2mm/.24”.

Letter stroke can be no smaller than .6mm

 

 

 

 

 

 

Previous Article Small Lettering Guide – Part 2
Next Article The Right Software For The Job
Print
31705 Rate this article:
5.0

6 comments on article "Small Lettering Guide – Part 1"

Avatar image

this

If you are interested in how they create design for computer games, then I advise you to read about it on specialized sites. This is very interesting and educational.


Avatar image

ivory

I like how the writer organized his thoughts in addition to he visual part.


Avatar image

andrew

I have read your blog. Honestly I've never read this type of blog before. Appreciate your work and will love to read your incoming articles too.

We have free online digitizer that can also fulfill your embroidery needs.


Avatar image

Donkey Kong

You've mentioned that pique, tees, and performance wear fabrics are stretchy, and as a result, small lettering becomes more challenging. In such cases, it is necessary to employ additional techniques like underlay to address these challenges effectively.


Avatar image

[url=https://tiny-fishing.com]tiny fishing[/url]

Thanks for the answer


Leave a comment

This form collects your name, email, IP address and content so that we can keep track of the comments placed on the website. For more info check our Privacy Policy and Terms Of Use where you will get more info on where, how and why we store your data.
Add comment

Theme picker

Working with 3D Puff Embroidery - Part 4

Working with 3D Puff Embroidery - Part 4

In this last installment, Jesse Elliott, our digitizing expert takes you through steps to remember when working with 3D puff designs.

Working with 3D Puff Embroidery - Part 3

Working with 3D Puff Embroidery - Part 3

In this third installment, Jesse Elliot, our digitizing expert takes you through the steps of embroidering a 3D puff design.

Gaining Visibility into Satisfaction Rates

Gaining Visibility into Satisfaction Rates

"Rate Your Project" is a feature on your Ignition Drawing Dashboard: Simply click to report your satifsfaction level. 

 

We offer Exact Sew Outs!

We offer Exact Sew Outs!

We wanted to give you more options to streamline your customer approval process. A lot of our customers resew our orders for customer approval which adds extra days and labor to the approval process. Where? - On the 3rd page...

Continue Reading →

Working with 3D Puff Embroidery - Part 2

Working with 3D Puff Embroidery - Part 2

Jesse Elliot, our digitizing expert, shares his insights in this second installment on how to digitize 3D puff embroidery.

RSS
12345